Pressure relief of underground ammunition storage under missile accidental ignition

Safety of underground ammunition storage is an important issue, especially during the accidental ignition of missiles. This work investigates the pressure and temperature distribution of the multi-layer underground ammunition storage with a pressure relief duct during the accidental ignition process of the missile. A large-scale experiment was carried out using a multi-layered restricted space with a pressure relief duct to simulate the underground ammunition store and a solid rocket motor to simulate the accidental ignition of the missile. The results show that when the motor gas mass flow increased by 5.6 times, the maximum pressure of the ammunition storage increased by 5.87 times. At a certain motor flow rate, when the pressure relief exhaust area at the end of the relief duct was reduced by 1/2, the maximum pressure on the first layer did not change. But the rate of pressure relief was reduced and the time delayed for the pressure of ammunition store to drop to zero. In this experiment, when the motor ignition position was located in to the third layer ammunition chamber, the maximum pressure was reduced by 32.9％ and also reduced the rate of change of pressure. In addition, for the experimental conditions, the theoretical analysis of the pressure relief of the ammunition storage is given by a simplified model. Based on the findings, some suggestions to the safety protection design of ammunition store are proposed.     

基于锥形量热法的油池火相似性及点火特性模拟实验

针对油料池火灾相似性及点火特性研究需要,构建了一种基于耗氧原理的油池火锥形量热法模拟实验系统,引入火灾尺度相似性概念,研究了实验室尺度油池火与真实尺度油池火的相似性关系,探讨了实验室尺度油池火预测真实尺度油池火的可行性,基于实验室尺度锥形量热法研究了油池火点火特性,得到了辐射强度、辐射距离对油料点燃时间的影响规律以及点燃时间与锥照射强度之间的拟合公式。     

温升热源条件油气热着火关键因素探究

通过对影响油气受热着火的关键因素进行研究,为发展主动防护技术提供理论依据。基于系统的实验和分析,探究了快速氧化现象、热源加热速度、热源面积与爆燃空间比例对热着火发生时临界浓度、着火概率和着火延迟期的影响,提出了温升热源条件受限空间能否发生热着火的综合判据。该判据认为：如果油气体积分数低于2.4％,受限空间体积与热源面积比值小于0．64m,那么即使温度达到873K,湿度降低到18％～21％,着火也不会发生。     

Controllable combustion behaviors of the laser-controlled solid propellant

Microsatellites have been widely applied in the fields of communication,remote sensing,navigation and science exploration due to its characteristics of low cost,flexible launch mode and short development period.However,conventional solid-propellant have difficulties in starting and interrupting combustion because combustion is autonomously sustained after ignition.Herein,we proposed a new type of solid-propellant named laser-controlled solid propellant,which is sensitive to laser irradiation and can be started or interrupted by switching on/off the continuous wave laser.To demonstrate the feasibility and investigate the controllable combustion behaviors under different laser on/off conditions,the combus-tion parameters including burning rate,ignition delay time and platform pressure were tested using pressure sensor,high-speed camera and thermographic camera.The results showed that the increase of laser-on or laser-off duration both will lead to the decrease of propellant combustion performance during re-ignition and re-combustion process.This is mainly attributed to the laser attenuation caused by the accumulation of combustion residue and the change of chamber ambient temperature.Simultaneously,the multiple ignition tests revealed that the increased chamber ambient temperature after combustion can make up for the energy loss of laser attenuation and expansion of chamber cavity.However,the laser-controlled combustion performance of solid propellant displayed a decrease trend with the addi-tion of ignition times.Nevertheless,the results still exhibited good laser-controlled agility of laser-controlled solid propellant and manifested its inspiring potential in many aspects of space missions.     

相对静止气氛下硼颗粒着火过程

针对相对静止气氛下单颗粒硼的着火过程展开了系统研究,考虑硼颗粒周围径向气相流动以及硼颗粒与周围环境间的传热和传质过程,建立了一维硼颗粒着火模型。分析了硼颗粒在实现着火和未能实现着火两种典型情形下的颗粒相、气相组分参数以及颗粒外表面上Stefan流的变化规律,并对其成因展开了分析。研究表明,在实现着火和未能实现着火两种典型情形下,硼颗粒外表面的Stefan流都会经历先由周围空间流向颗粒表面,而后变为由颗粒表面流向周围空间的过程;考虑颗粒外表面处气相Stefan流作用后,硼颗粒的着火延迟时间减少,且压力越大,影响越大。     

铝导线短路熔珠对固体可燃物引燃能力实验研究

在模拟试验平台上进行了铝导线短路熔珠引燃棉布、聚氨酯泡沫塑料和纸张的试验，得到了不同材料的临界加栽电压值和引燃规律。初步分析了加栽电压与短路熔珠粒径及引燃能力的关系。结果表明，随着短路电压增大，导线熔珠的粒径逐渐增大，熔珠对固体材料的引燃能力逐渐增强，氧指数越低、表面粗糙、易蓄热的材料越容易被点燃。棉布、聚氨酯泡沫塑料和纸屑被引燃的短路临界电压分别为50V、35V和45V。     

固体发动机尾部点火性能影响因素分析

采用准一维非定常数值模型,对某小型固体发动机尾部点火瞬态过程进行性能预示;以预示结果为基础,对尾部点火性能主要影响因素进行了参数研究.研究结果可为尾部点火器和喷管堵盖的点火匹配性设计提供有益指导.     

导线过负荷引燃能力的模拟实验研究

为了考查导线过负荷对不同可燃物的引燃能力，选择1．5,2．5和4mm^2三种规格的铝导线在不同倍数过负荷电流条件下进行实验，测得导线温度并观察过负荷导线对火场中常见的棉布、阻燃管、防水板的引燃能力。通过实验得出过负荷导线引燃能力与导线截面积、过负荷时间、过负荷电流的大小的关系，并讨论了可燃物种类对过负荷导线引燃能力的影响。结果表明，过负荷导线的引燃能力与过负荷电流和时间成正比，而导线的截面积对引燃能力的影响是多方面的。为防止火灾发生，在建筑物中布置导线时要远离可燃物并要穿阻燃管铺设。     

室内装饰织物燃烧特性研究

室内装饰织物因其容易点燃、燃烧速度快、蔓延迅速等燃烧特性,对室内火灾的发展蔓延及火灾危害都有重要影响。运用锥形量热仪对棉麻、涤纶、帆布、泡纱、条绒等5种室内装饰织物的燃烧性能进行了实验研究,测量了室内装饰织物在不同热辐射条件下的燃烧特性,并对实验数据进行图像拟合,通过具体的实验数据和图像分析比较了5种室内装饰织物在不同热辐射条件下的点燃时间、热释放速率、质量损失速率、比消光面积及CO生成量。最后得出了各种织物的火灾危险性相对大小。     

驱动管中柱状装药爆轰过程的数值模拟

数值模拟了爆炸驱动管中柱状装药内爆轰波的传播过程.计算采用欧拉型有限体积方法,炸药及爆轰产物均采用JWL状态方程,空气采用理想气体状态方程,采用"点火-生长"模型计算化学反应速率.计算得到了驱动管内波系结构的发展过程,爆速与经验公式符合得较好.计算表明,驱动管侧壁的压力峰值在800MPa以上,而在管底中心处,由于激波的汇聚,压力峰值高达12.4GPa.